How to use the MonoWing script - Revision history

Amounra at 09:58, 16 January 2015

2015-01-16T09:58:39Z

Amounra at 09:34, 16 January 2015

2015-01-16T09:34:56Z

Amounra: Created page with "Modes: Looper Mode Each of the bottom 4 rectangular buttons represent one of four loopers. A looper can be an instance of Live's built in looper, or Jove (from Monomodular)..."

2015-01-16T09:33:58Z

Created page with "Modes: Looper Mode Each of the bottom 4 rectangular buttons represent one of four loopers. A looper can be an instance of Live's built in looper, or Jove (from Monomodular)..."

New page

Modes:

Looper Mode

Each of the bottom 4 rectangular buttons represent one of four loopers. A looper can be an instance of Live's built in looper, or Jove (from Monomodular). Preface the looper name with "@looper" and it's number.

Select the loop by using the four select buttons. The color of each button represents its corresponding looper's state:

Red: recording.
Cyan: overdubbing.
Blue: muted.
Green: playing.
Magenta: waiting to sync (for quantized features).
White: selected.

The round pads control loop functions for the selected loop, and the long slider controls feedback amount. The buttons are: Overdub, Record, Mute, Reverse, and Clear (on the tip of the wing).

Scene Launcher Mode

The select buttons select from banks 1 - 4. In each bank, there are 4 launch buttons. This allows launching up to 16 scenes. Preface a scene with "@launch" + the bank number + the slot number. (e.g. "@launch 1 1").

Device Mode

The select buttons select from devices 1 - 4 (designated by prefacing device name with "@fx" + its number, e.g. "@fx1"). Each device should be a rack. The pad buttons allow toggling of macros, while the long slider allows continuous control. By renaming the macro controls in the device to "@param" + its number, you can toggle its value between 0 and 127 by pressing the button. By renaming one of the macro controls to "@exp", you can control its value with the long slider.

To designate a rack to be used for one

← Older revision		Revision as of 09:58, 16 January 2015
Line 24:		Line 24:
	Device Mode		Device Mode

−	The select buttons select from devices 1 - 4 (designated by prefacing device name with "@fx" + its number, e.g. "@~~fx1~~"). Each device should be a rack. The pad buttons allow toggling of macros, while the long slider allows continuous control. By renaming the macro controls in the device to "@~~param~~" + its number, you can toggle its value between 0 and 127 by pressing the button. By renaming one of the macro controls to "@exp", you can control its value with the ~~long slider~~.	+	The select buttons select from devices 1 - 4 (designated by prefacing device name with "@fx:" + its number, e.g. "@fx:1"). Each device should be a rack. The pad buttons allow toggling of macros, while the long slider allows continuous control. By renaming the macro controls in the device to "@prm:" + its number, you can toggle its value between 0 and 127 by pressing the button. By renaming one of the macro controls to "@exp:" + its number, you can control its value with one of the sliders.

@@ Line 1: / Line 1: @@
 Modes:
 Looper Mode
@@ Line 23: / Line 25: @@
 The select buttons select from devices 1 - 4 (designated by prefacing device name with "@fx" + its number, e.g. "@fx1").  Each device should be a rack.  The pad buttons allow toggling of macros, while the long slider allows continuous control.  By renaming the macro controls in the device to "@param" + its number, you can toggle its value between 0 and 127 by pressing the button.  By renaming one of the macro controls to "@exp", you can control its value with the long slider.